# Flags
Here is the latest, up to date Flags list.
This file was autogenerated by running 'node scripts/getcommands.js' in the repository.
All descriptions were taken from code.
Do not add anything here, as it will overwritten with next rebuild.
| ID |   Description  |
|:--| -------:|
| 0 | [MQTT] Broadcast led params together (send dimmer and color when dimmer or color changes, topic name: YourDevName/led_basecolor_rgb/get, YourDevName/led_dimmer/get)", |
| 1 | [MQTT] Broadcast led final color (topic name: YourDevName/led_finalcolor_rgb/get)", |
| 2 | [MQTT] Broadcast self state every N (def: 60) seconds (delay configurable by 'mqtt_broadcastInterval' and 'mqtt_broadcastItemsPerSec' commands)", |
| 3 | [LED][Debug] Show raw PWM controller on WWW index instead of new LED RGB/CW/etc picker", |
| 4 | [LED] Force show RGBCW controller (for example, for SM2135 LEDs, or for DGR sender)", |
| 5 | [CMD] Enable TCP console command server (for Putty, etc)", |
| 6 | [BTN] Instant touch reaction instead of waiting for release (aka SetOption 13)", |
| 7 | [MQTT] [Debug] Always set Retain flag to all published values", |
| 8 | [LED] Alternate CW light mode (first PWM for warm/cold slider, second for brightness)", |
| 9 | [SM2135] Use separate RGB/CW modes instead of writing all 5 values as RGB", |
| 10 | [MQTT] Broadcast self state on MQTT connect", |
| 11 | [PWM] BK7231 use 600hz instead of 1khz default", |
| 12 | [LED] Remember LED driver state (RGBCW, enable, brightness, temperature) after reboot", |
| 13 | [HTTP] Show actual PIN logic level for unconfigured pins", |
| 14 | [IR] Do MQTT publish (RAW STRING) for incoming IR data", |
| 15 | [IR] Allow 'unknown' protocol", |
| 16 | [MQTT] Broadcast led final color RGBCW (topic name: YourDevName/led_finalcolor_rgbcw/get)", |
| 17 | [LED] Automatically enable Light when changing brightness, color or temperature on WWW panel", |
| 18 | [LED] Smooth transitions for LED (EXPERIMENTAL)", |
| 19 | [MQTT] Always publish channels used by TuyaMCU", |
| 20 | [LED] Force RGB mode (3 PWMs for LEDs) and ignore futher PWMs if they are set", |
| 21 | [MQTT] Retain power channels (Relay channels, etc)", |
| 22 | [IR] Do MQTT publish (Tasmota JSON format) for incoming IR data", |
| 23 | [LED] Automatically enable Light on any change of brightness, color or temperature", |
| 24 | [LED] Emulate Cool White with RGB in device with four PWMS - Red is 0, Green 1, Blue 2, and Warm is 4", |
| 25 | [POWER] Allow negative current/power for power measurement (all chips, BL0937, BL0942, etc)", |
| 26 | [UART] Use alternate UART for BL0942, CSE, TuyaMCU, etc", |
| 27 | [HASS] Invoke HomeAssistant discovery on change to ip address, configuration", |
| 28 | [LED] Setting RGB white (FFFFFF) enables temperature mode", |
| 29 | [NETIF] Use short device name as a hostname instead of a long name", |
| 30 | [MQTT] Enable Tasmota TELE etc publishes (for ioBroker etc)", |
| 31 | [UART] Enable UART command line", |
| 32 | [LED] Use old linear brightness mode, ignore gamma ramp", |
| 33 | [MQTT] Apply channel type multiplier on (if any) on channel value before publishing it", |
| 34 | [MQTT] In HA discovery, add relays as lights", |
| 35 | [HASS] Deactivate avty_t flag for sensor when publishing to HASS (permit to keep value)", |
| 36 | [DRV] Deactivate Autostart of all drivers", |
| 37 | [WiFi] Quick connect to WiFi on reboot (TODO: check if it works for you and report on github)", |