[ Upstream commit baeb66fbd4201d1c4325074e78b1f557dff89b5b ]
A race condition during gadget teardown can lead to a use-after-free
in usb_gadget_state_work(), as reported by KASAN:
BUG: KASAN: invalid-access in sysfs_notify+0x2c/0xd0
Workqueue: events usb_gadget_state_work
The fundamental race occurs because a concurrent event (e.g., an
interrupt) can call usb_gadget_set_state() and schedule gadget->work
at any time during the cleanup process in usb_del_gadget().
Commit 399a45e5237c ("usb: gadget: core: flush gadget workqueue after
device removal") attempted to fix this by moving flush_work() to after
device_del(). However, this does not fully solve the race, as a new
work item can still be scheduled *after* flush_work() completes but
before the gadget's memory is freed, leading to the same use-after-free.
This patch fixes the race condition robustly by introducing a 'teardown'
flag and a 'state_lock' spinlock to the usb_gadget struct. The flag is
set during cleanup in usb_del_gadget() *before* calling flush_work() to
prevent any new work from being scheduled once cleanup has commenced.
The scheduling site, usb_gadget_set_state(), now checks this flag under
the lock before queueing the work, thus safely closing the race window.
Fixes: 5702f75375 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue")
Cc: stable <stable@kernel.org>
Signed-off-by: Jimmy Hu <hhhuuu@google.com>
Link: https://patch.msgid.link/20251023054945.233861-1-hhhuuu@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Adjust context ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulrich Hecht <uli@kernel.org>
commit 0d9cfc9b8cb17dbc29a98792d36ec39a1cf1395f upstream.
The Gemalto Cinterion PLS83-W modem (cdc_ether) is emitting confusing link
up and down events when the WWAN interface is activated on the modem-side.
Interrupt URBs will in consecutive polls grab:
* Link Connected
* Link Disconnected
* Link Connected
Where the last Connected is then a stable link state.
When the system is under load this may cause the unlink_urbs() work in
__handle_link_change() to not complete before the next usbnet_link_change()
call turns the carrier on again, allowing rx_submit() to queue new SKBs.
In that event the URB queue is filled faster than it can drain, ending up
in a RCU stall:
rcu: INFO: rcu_sched detected expedited stalls on CPUs/tasks: { 0-.... } 33108 jiffies s: 201 root: 0x1/.
rcu: blocking rcu_node structures (internal RCU debug):
Sending NMI from CPU 1 to CPUs 0:
NMI backtrace for cpu 0
Call trace:
arch_local_irq_enable+0x4/0x8
local_bh_enable+0x18/0x20
__netdev_alloc_skb+0x18c/0x1cc
rx_submit+0x68/0x1f8 [usbnet]
rx_alloc_submit+0x4c/0x74 [usbnet]
usbnet_bh+0x1d8/0x218 [usbnet]
usbnet_bh_tasklet+0x10/0x18 [usbnet]
tasklet_action_common+0xa8/0x110
tasklet_action+0x2c/0x34
handle_softirqs+0x2cc/0x3a0
__do_softirq+0x10/0x18
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
__irq_exit_rcu+0xa8/0xb8
irq_exit_rcu+0xc/0x30
el1_interrupt+0x34/0x48
el1h_64_irq_handler+0x14/0x1c
el1h_64_irq+0x68/0x6c
_raw_spin_unlock_irqrestore+0x38/0x48
xhci_urb_dequeue+0x1ac/0x45c [xhci_hcd]
unlink1+0xd4/0xdc [usbcore]
usb_hcd_unlink_urb+0x70/0xb0 [usbcore]
usb_unlink_urb+0x24/0x44 [usbcore]
unlink_urbs.constprop.0.isra.0+0x64/0xa8 [usbnet]
__handle_link_change+0x34/0x70 [usbnet]
usbnet_deferred_kevent+0x1c0/0x320 [usbnet]
process_scheduled_works+0x2d0/0x48c
worker_thread+0x150/0x1dc
kthread+0xd8/0xe8
ret_from_fork+0x10/0x20
Get around the problem by delaying the carrier on to the scheduled work.
This needs a new flag to keep track of the necessary action.
The carrier ok check cannot be removed as it remains required for the
LINK_RESET event flow.
Fixes: 4b49f58fff ("usbnet: handle link change")
Cc: stable@vger.kernel.org
Signed-off-by: John Ernberg <john.ernberg@actia.se>
Link: https://patch.msgid.link/20250723102526.1305339-1-john.ernberg@actia.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
[ adjust context in header ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulrich Hecht <uli@kernel.org>
commit af4db5a35a4ef7a68046883bfd12468007db38f1 upstream.
A poorly implemented DisplayPort Alt Mode port partner can indicate
that its pin assignment capabilities are greater than the maximum
value, DP_PIN_ASSIGN_F. In this case, calls to pin_assignment_show
will cause a BRK exception due to an out of bounds array access.
Prevent for loop in pin_assignment_show from accessing
invalid values in pin_assignments by adding DP_PIN_ASSIGN_MAX
value in typec_dp.h and using i < DP_PIN_ASSIGN_MAX as a loop
condition.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable <stable@kernel.org>
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20250618224943.3263103-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulrich Hecht <uli@kernel.org>
[ Upstream commit a769154c7cac037914ba375ae88aae55b2c853e0 ]
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 1e0a19912adb ("usb: xhci: Fix NULL pointer dereference on certain command aborts")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ulrich Hecht <uli@kernel.org>
commit 130eac4170859fb368681e00d390f20f44bbf27b upstream.
A recent patch caused an unused-function warning in builds with
CONFIG_PM disabled, after the function became marked 'static':
drivers/usb/host/xhci-pci.c:91:13: error: 'xhci_msix_sync_irqs' defined but not used [-Werror=unused-function]
91 | static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
| ^~~~~~~~~~~~~~~~~~~
This could be solved by adding another #ifdef, but as there is
a trend towards removing CONFIG_PM checks in favor of helper
macros, do the same conversion here and use pm_ptr() to get
either a function pointer or NULL but avoid the warning.
As the hidden functions reference some other symbols, make
sure those are visible at compile time, at the minimal cost of
a few extra bytes for 'struct usb_device'.
Fixes: 9abe15d55dcc ("xhci: Move xhci MSI sync function to to xhci-pci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230328131114.1296430-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulrich Hecht <uli@kernel.org>
[ Upstream commit 0fa81b304a7973a499f844176ca031109487dd31 ]
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7e01c7f7046e ("net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1e5c2f0cb8a22ec2e14af92afc7006491bebabb upstream.
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c6c2f8a907c9e3a2f24990552a4d77235791e6 upstream.
Usb core introduce the mechanism of giveback of URB in tasklet context to
reduce hardware interrupt handling time. On some test situation(such as
FIO with 4KB block size), when tasklet callback function called to
giveback URB, interrupt handler add URB node to the bh->head list also.
If check bh->head list again after finish all URB giveback of local_list,
then it may introduce a "dynamic balance" between giveback URB and add URB
to bh->head list. This tasklet callback function may not exit for a long
time, which will cause other tasklet function calls to be delayed. Some
real-time applications(such as KB and Mouse) will see noticeable lag.
In order to prevent the tasklet function from occupying the cpu for a long
time at a time, new URBS will not be added to the local_list even though
the bh->head list is not empty. But also need to ensure the left URB
giveback to be processed in time, so add a member high_prio for structure
giveback_urb_bh to prioritize tasklet and schelule this tasklet again if
bh->head list is not empty.
At the same time, we are able to prioritize tasklet through structure
member high_prio. So, replace the local high_prio_bh variable with this
structure member in usb_hcd_giveback_urb.
Fixes: 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet context")
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220726074918.5114-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6f1488abeca594d377991171c00e52a upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6490fa565534fa83593278267785a694fd378a2b upstream.
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de658a195ee23ca6aaffe197d1d2ea040beea0a2 ]
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bbe2a90a0bb4af8dd99c3565e907fe9b5e7fd88 ]
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc7eac1e4afdd151085be4d0341a155760388653 ]
Since EHCI/OHCI controllers on R-Car Gen3 SoCs are possible to
be getting stuck very rarely after a full/low usb device was
disconnected. To detect/recover from such a situation, the controllers
require a special way which poll the EHCI PORTSC register and changes
the OHCI functional state.
So, this patch adds a polling timer into the ehci-platform driver,
and if the ehci driver detects the issue by the EHCI PORTSC register,
the ehci driver removes a companion device (= the OHCI controller)
to change the OHCI functional state to USB Reset once. And then,
the ehci driver adds the companion device again.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1580114262-25029-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d363120aa548ba52d58907a295eee25f8207ed2 ]
This patch adds new config_ep_by_speed_and_alt function which
extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint
address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 73f8bda9b5dc1c69df2bc55c0cbb24461a6391a9 upstream.
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 17a0184ca17e288decdca8b2841531e34d49285f upstream.
Commit e0d795e4f3 ("usb: irda: cleanup on ir-usb module") added a USB
IrDA header with common defines, but mistakingly switched to using the
class-descriptor baud-rate bitmask values for the outbound header.
This broke link-speed handling for rates above 9600 baud, but a device
would also be able to operate at the default 9600 baud until a
link-speed request was issued (e.g. using the TCGETS ioctl).
Fixes: e0d795e4f3 ("usb: irda: cleanup on ir-usb module")
Cc: stable <stable@vger.kernel.org> # 2.6.27
Cc: Felipe Balbi <balbi@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7893f9e1c26d1f9ea02622902ee671de45ad377b ]
Some tcpc device-drivers need to explicitly be told to watch for connection
events, otherwise the tcpc will not generate any TCPM_CC_EVENTs and devices
being plugged into the Type-C port will not be noticed.
For dual-role ports tcpm_start_drp_toggling() is used to tell the tcpc to
watch for connection events. Sofar we lack a similar callback to the tcpc
for single-role ports. With some tcpc-s such as the fusb302 this means
no TCPM_CC_EVENTs will be generated when the port is configured as a
single-role port.
This commit renames start_drp_toggling to start_toggling and since the
device-properties are parsed by the tcpm-core, adds a port_type parameter
to the start_toggling callback so that the tcpc_dev driver knows the
port-type and can act accordingly when it starts toggling.
The new start_toggling callback now always gets called if defined, instead
of only being called for DRP ports.
To avoid this causing undesirable functional changes all existing
start_drp_toggling implementations are not only renamed to start_toggling,
but also get a port_type check added and return -EOPNOTSUPP when port_type
is not DRP.
Fixes: ea3b4d5523bc("usb: typec: fusb302: Resolve fixed power role ...")
Cc: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 23b5f73266e59a598c1e5dd435d87651b5a7626b ]
During HARD_RESET the data link is disconnected.
For self powered device, the spec is advising against doing that.
>From USB_PD_R3_0
7.1.5 Response to Hard Resets
Device operation during and after a Hard Reset is defined as follows:
Self-powered devices Should Not disconnect from USB during a Hard Reset
(see Section 9.1.2).
Bus powered devices will disconnect from USB during a Hard Reset due to the
loss of their power source.
Tackle this by letting TCPM know whether the device is self or bus powered.
This overcomes unnecessary port disconnections from hard reset.
Also, speeds up the enumeration time when connected to Type-A ports.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
---------
Version history:
V3:
Rebase on top of usb-next
V2:
Based on feedback from heikki.krogerus@linux.intel.com
- self_powered added to the struct tcpm_port which is populated from
a. "connector" node of the device tree in tcpm_fw_get_caps()
b. "self_powered" node of the tcpc_config in tcpm_copy_caps
Based on feedbase from linux@roeck-us.net
- Code was refactored
- SRC_HARD_RESET_VBUS_OFF sets the link state to false based
on self_powered flag
V1 located here:
https://lkml.org/lkml/2018/9/13/94
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 781f0766cc41a9dd2e5d118ef4b1d5d89430257b upstream.
Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[ 206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[ 206.143691] usb 3-2.4: device descriptor read/64, error -32
[ 206.351671] usb 3-2.4: device descriptor read/64, error -32
Info for this hub:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1a40 ProdID=0101 Rev=01.11
S: Product=USB 2.0 Hub
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.
Hence wait for extra delay, if the device is connected to this quirky
hub.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB/PHY updates from Greg KH:
"Here is the big USB and phy driver patch set for 4.19-rc1.
Nothing huge but there was a lot of work that happened this
development cycle:
- lots of type-c work, with drivers graduating out of staging, and
displayport support being added.
- new PHY drivers
- the normal collection of gadget driver updates and fixes
- code churn to work on the urb handling path, using irqsave()
everywhere in anticipation of making this codepath a lot simpler in
the future.
- usbserial driver fixes and reworks
- other misc changes
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (159 commits)
USB: serial: pl2303: add a new device id for ATEN
usb: renesas_usbhs: Kconfig: convert to SPDX identifiers
usb: dwc3: gadget: Check MaxPacketSize from descriptor
usb: dwc2: Turn on uframe_sched on "stm32f4x9_fsotg" platforms
usb: dwc2: Turn on uframe_sched on "amlogic" platforms
usb: dwc2: Turn on uframe_sched on "his" platforms
usb: dwc2: Turn on uframe_sched on "bcm" platforms
usb: dwc2: gadget: ISOC's starting flow improvement
usb: dwc2: Make dwc2_readl/writel functions endianness-agnostic.
usb: dwc3: core: Enable AutoRetry feature in the controller
usb: dwc3: Set default mode for dwc_usb31
usb: gadget: udc: renesas_usb3: Add register of usb role switch
usb: dwc2: replace ioread32/iowrite32_rep with dwc2_readl/writel_rep
usb: dwc2: Modify dwc2_readl/writel functions prototype
usb: dwc3: pci: Intel Merrifield can be host
usb: dwc3: pci: Supply device properties via driver data
arm64: dts: dwc3: description of incr burst type
usb: dwc3: Enable undefined length INCR burst type
usb: dwc3: add global soc bus configuration reg0
usb: dwc3: Describe 'wakeup_work' field of struct dwc3_pci
...
Thee USB Audio Class 3 (UAC3) introduces Power Domains as a new
feature to let a host turn individual parts of an audio function
to different power states via USB requests. This lets the device
get to know a bit amore about what the host is up to in order to
optimize power consumption efficiently.
The Power Domains are optional for UAC3 configuration but all
UAC3 devices shall include at least one BADD configuration where
the support for Power Domains is compulsory.
This patch adds a set of features/helpers to parse these power
domains and change their status.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Processig Units defined in
the UAC3 spec. The main difference with the previous specs
is the lack of on/off switches in the controls for these
units and the addiction of the new Multi Function Processing
Unit.
The current version of the UAC3 spec doesn't define any
useful controls for the new Multi Function Processing Unit
so no control will get created once this unit is parsed.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds more complete handling of VDMs and registration of
partner alternate modes, and introduces callbacks for
alternate mode operations.
Only DFP role is supported for now.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introducing a simple bus for the alternate modes. Bus allows
binding drivers to the discovered alternate modes the
partners support.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before a device was created for every discovered SVID, but
this will create a device for every discovered mode of every
SVID. The idea is to make it easier to create mode specific
drivers once a bus for the alternate mode is added.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for the muxes to be usable with alternate modes,
the alternate mode devices will need also to be able to get
a handle to the muxes on top of the port devices. To make
that possible, the muxes need to be possible to request with
an identifier.
This will change the API so that the mux identifier is given
as a function parameter to typec_mux_get(), and the hard-coded
"typec-mux" is replaced with that value.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds function typec_get_orientation() that can be used
for checking the current cable plug orientation.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This makes life a bit easier for the drivers that include
pd.h. All pd_header_*_le() inline functions defined in pd.h
call le16_to_cpu(), and all *_LE() macros in pd.h call
cpu_to_le16().
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device attached to a root-hub port sends a wakeup request
to a sleeping system, we do not report the wakeup event to the PM
core. This is because a system resume involves waking up all
suspended USB ports as quickly as possible; without the normal
USB_RESUME_TIMEOUT delay, the host controller driver doesn't set the
USB_PORT_STAT_C_SUSPEND flag and so usb_port_resume() doesn't realize
that a wakeup request was received.
However, some environments (such as Chrome OS) want to have all wakeup
events reported so they can be ascribed to the appropriate device. To
accommodate these environments, this patch adds a new routine to the
hub driver and a corresponding new HCD method to be used when a root
hub resumes. The HCD method returns a bitmap of ports that have
initiated a wakeup signal but not yet completed resuming. The hub
driver can then report to the PM core that the child devices attached
to these ports initiated a wakeup event.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull sound updates from Takashi Iwai:
"We've got many code additions at this cycle as a result of quite a few
new drivers. Below are highlights:
Core stuff:
- Fix the long-standing issue with the device registration order; the
control device is now registered at last
- PCM locking code cleanups for RT kernels
- Fixes for possible races in ALSA timer resolution accesses
- TLV offset definitions in uapi
ASoC:
- Many fixes for the topology stuff, including fixes for v4 ABI
compatibility
- Lots of cleanups / quirks for Intel platforms based on Realtek
CODECs
- Continued componentization works, removing legacy CODEC stuff
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver
- Fixes and updates to Cirrus Logic SoC drivers
- New Qualcomm DSP support
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306
and RT5668 and TI TSCS454
HD-audio:
- Finally better support for some CA0132 boards, allowing Windows
firmware
- HP Spectre x360 support along with a bulk of COEF stuff
- Blacklisting power save default some known boards reported on
Fedora
USB-audio:
- Continued improvements on UAC3 support; now BADD is supported
- Fixes / improvements for Dell WD15 dock
- Allow DMA coherent pages for PCM buffers for ARCH, MIPS & co
Others:
- New Xen sound frontend driver support
- Cache implementation and other improvements for FireWire DICE
- Conversions to octal permissions in allover places"
* tag 'sound-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (386 commits)
ASoC: dapm: delete dapm_kcontrol_data paths list before freeing it
ALSA: usb-audio: remove redundant check on err
ASoC: topology: Move skl-tplg-interface.h to uapi
ASoC: topology: Move v4 manifest header data structures to uapi
ASoC: topology: Improve backwards compatibility with v4 topology files
ALSA: pci/hda: Remove unused, broken, header file
ASoC: TSCS454: Add Support
ASoC: Intel: kbl: Move codec sysclk config to codec_init function
ASoC: simple-card: set cpu dai clk in hw_params
ALSA: hda - Handle kzalloc() failure in snd_hda_attach_pcm_stream()
ALSA: oxygen: use match_string() helper
ASoC: dapm: use match_string() helper
ASoC: max98095: use match_string() helper
ASoC: max98088: use match_string() helper
ASoC: Intel: bytcr_rt5651: Set card long_name based on quirks
ASoC: mt6797-mt6351: add hostless phone call path
ASoC: mt6797: add Hostless DAI
ASoC: mt6797: add PCM interface
ASoC: mediatek: export mtk-afe symbols as needed
ASoC: codecs: PCM1789: include gpio/consumer.h
...
usb: changes for v4.18 merge window
A total of 98 non-merge commits, the biggest part being in dwc3 this
time around with a large refactoring of dwc3's transfer handling code.
We also have a new driver for Aspeed virtual hub controller.
Apart from that, just a list of miscellaneous fixes all over the place.
The following members in struct musb_hdrc_config are not used,
so remove them.
soft_con
utm_16
big_endian
mult_bulk_tx
mult_bulk_rx
high_iso_tx
high_iso_rx
dma
dma_channels
dyn_fifo_size
vendor_ctrl
vendor_stat
vendor_req
dma_req_chan
musb_hdrc_eps_bits
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The composite framework allows us to create gadgets composed from many
different functions, which need to fit into a single configuration
descriptor.
Some functions (like uvc) can produce configuration descriptors upwards
of 2500 bytes on their own.
This patch increases the limit from 1024 bytes to 4096.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The table is never modified by the function. This allows us
to use it on a statically defined table that is marked const.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This adds support for the UAC3 insertion controls. The status
is reported as a boolean value in the same way it used to do
for UAC2. Hence, the presence of any connector in the response
will make the control saying the jack is connected.
The UAC2 support for this control has been moved to a dedicated
control for connectors as both UAC2 and UAC3 follow a specific
Control Request Parameter Block for this control. This parameter
block for UAC3 could not be read in the same simplistic
manner as in UAC2.
This implementation is not requesting additional information
from the HIGH CAPABILITY Connectors descriptor.
Tested with an UAC3 device with UAC2 as legacy configuration.
The connector status can be read with `amixer` and the interrupt
is also caught with `alsactl monitor`.
Signed-off-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add BADD-specific predefined values to audio-v3
so usb-audio in ALSA and UAC3 gadget can use them
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The composite framework allows us to create gadgets composed from many
different functions, which need to fit into a single configuration
descriptor.
Some functions (like uvc) can produce configuration descriptors upwards
of 2500 bytes on their own.
This patch increases the limit from 1024 bytes to 4096.
Signed-off-by: Joel Pepper <joel.pepper@rwth-aachen.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This commit adds code to handle requesting of PPS APDOs. Switching
between standard PDOs and APDOs, and re-requesting an APDO to
modify operating voltage/current will be triggered by an
external call into TCPM.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UTMI pads are shared by USB controllers and reset of UTMI pads is shared
with the reset of USB1 controller. Currently reset of UTMI pads is done by
the EHCI driver and ChipIdea UDC works because EHCI driver always happen
to be probed first. Move reset controls from ehci-tegra to tegra-phy in
order to resolve the problem.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.2 Enhaned SuperSpeed can set their hcd speed
to HCD_USB32 to let usb core and host drivers know that the controller
supports new USB 3.2 dual-lane features.
make sure usb core handle HCD_USB32 hosts correctly, for now similar
to HCD_USB32.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The legacy interface for associating controllers with phys from board
files and platform code has been unused since commit 9080b8dc76 ("ARM:
OMAP2+: Remove legacy usb-host.c platform init code"). Since then, all
calls to usb_get_phy_dev() and its devres version have been returning
-ENODEV.
Now that the final calls to these functions have been removed, we can
drop this legacy lookup interface altogether.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for looking up and initialising legacy phys in USB core,
something which hasn't been used by a mainline kernel since commit
9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c platform init
code"). Specifically, since that commit usb_get_phy_dev() have always
returned -ENODEV and consequently this code has not been used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the unused legacy usb_bind_phy() helper whose last user was removed
in 2016 when OMAP moved to device-tree boot (9080b8dc76 ("ARM: OMAP2+:
Remove legacy usb-host.c platform init code")).
Note that this means that for the last couple of years the phy_bind_list
has been empty (when using mainline kernels) and that consequently all
phy lookups using the usb_get_phy_dev() interface have failed with
-ENODEV. This helper along with its current users will be removed by
follow-on patches.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
